| |
Team Experience | |
 Client: Ministry of Electricity, Baghdad, Iraq
Salihi Group International (SGI).
Project Description: The project is to construct a 400 MV BOO power plant in Chimchimal. Estimated cost is $120 million US Dollars and its is scheduled to be completed at the end of 2006. SGI is executing all construction work, including all security and life support for the project facilities and personnel.
 Client: Dibis Military Water Treatment, Kirkuk, Iraq
Salihi Group International (SGI).
Project Description: SGI renovated all electrical systems, replacing four 6000 volt transformers, replacing all underground cables, replacing all high pressure pumps 75 HP; install new doors, windows, and repainting the whole plant. Installation of a computerized control room for the plant. Operating the plant and training new government staff to run the plant professionally. Transferring the plant to operational control of the Kirkuk Water and Sewer Department. Provide security service to secure the site, establishing security for team housing on site, clearing the site of bombs, weapons, hazards, materials and removing debris from the site. The head of the water department, Mr. Abdulkader, announced his appreciation for the quality job that SGI completed under the most difficult environment in the city of Dibis where violence and bombs are common incidents of every work day.
Client: Ministry of Electricity, Baiji Thermal Power Station, Iraq
Al Merjal General Contracting Co. Ltd. (MERGCC).
Project Description: Provided Rehabilitation of Water Tubes Panels of Boiler unit 5 at Baiji Thermal Power Station.
Client: Ministry of Electricity, Baiji Gas Power Station, Iraq
Al Merjal General Contracting Co. Ltd. (MERGCC).
Project Description: Erection of two Heavy Oil Storage Tanks, each of 4500m3.
 Client: Babcock Borsig Power Service GmbH, Germany
Al Merjal General Contracting Co. Ltd. (MERGCC).
Project Description: Rehabilitation of Boiler units 5 & 6 at Douro Thermal Power Station.
 Client: Bechtel International Systems, Inc. Co. of USA
Al Merjal General Contracting Co. Ltd. (MERGCC).
Project Description: General Resource Services for Baiji Power Station (Provide craft, labor, equipment operators, supervision, administrative and management services, procurement and field engineering necessary to support the rehabilitation of the Baiji Power Station, Units 1, 2, 3, 4, & 6).
 Client: US Army, Coalition Forces, Iraq
Al Agha Construction and General Trade (Al-Agha).
Project Description: Acquisition and Installation of Power Generators.
Client: Ministry of Electricity, Kirkuk, Iraq
Al Agha Construction and General Trade (Al-Agha).
Project Description: Electro – Mechanical Renovations for the High and Low Tension Electrical Station Networks.
 Client: US Army Corps of Engineers, Iraq
Al Agha Construction and General Trade (Al-Agha).
Product Description: Design and Construct a Water Treatment Plant, 11400m3/day.
Client: US Army Corps of Engineers, Iraq
Sameh Sadar Group (SSG).
Project Description: SSG is providing engineering services to USACE for the entire GRN which includes all staff and services necessary to provide Human Resources and Payroll Support ATC Services in the Gulf Region North for all ATC Services, Inc. employees.
 Client: The U.S. Navy
Air New Zealand Engineering Services (ANZES).
Project Description: ANZES provided overhaul of U.S. Navy LM2500 single shank (GGA-180) engine which was successfully completed in March 2003. The US Navy is the world’s largest user of the LM2500 engine with over 450 LM2500 Gas Turbine Engines used for shipboard propulsion. Commencing in October 2002 with a very detailed work scope meeting, the engineers at ANZES demonstrated their technical expertise and thorough understanding of the overhaul requirements set forth by the US Navy. ANZES sustained a very informative and recurring dialogue with the US Navy throughout the entire duration of the overhaul that nullified time difference and geographic distance between the two organizations.
 Client: AES Nigeria Barge Ltd. Egbin, Nigeria
Turbine Technology Services Corporation (TTS).
Project Description: Nine (9) MS6001 gas turbine generator power barges relocated from the Philippines to Nigeria. Duel fuel conversion. Gas turbine and generator control system retrofit. 50 to 60 Hz conversions to generator and all barge mounted electrical equipment. Generator overhaul. Turbine start-up and commissioning. Full balance of plant start up and commissioning.
 Client: City of Pasadena, California, USA
Turbine Technology Services (TTS).
Project Description: All work was performed on two adjoining sites separated by a local mass transit rail system. Site work: Mass excavations for foundations and underground utilities including backfill and testing. Pull boxes, sewer, storm and outfall for both sites. Structural: All reinforced concrete foundations including rebar, concrete, imbeds and concrete piles. Electrical: Conduit, cable tray, wire, instrumentation; service up to and including 13.8kV. Testing including; continuity, point to point, megger, hi pot, relay and calibrations. Mechanical Equipment: Setting and alignment of all equipment. Procurement of Demin. tanks and gas compressor building.
Client: City of Fresno, California, USA
Turbine Technology Services (TTS).
Project Description: All work was done to refurbish a relocated combined cycle cogeneration facility. Facility consists of two CTG's, two HRSG's and one steam turbine. Structural: Foundations for contractor supplied equipment including digester skid, cooling tower and support steel. Electrical: Design and install medium and low voltage distribution. Conduit, cable tray, wire and instrumentation. Mechanical Equipment: Refurbishment and installation of Owner supplied equipment. Design and install new equipment including digester gas skid, cooling tower, dump condenser, CEMS and miscellaneous pumps.
 Client: Sacramento Municipal Utility District (SMUD)
Turbine Technology Services (TTS).
Project Description: Electrical: Conduit, cable tray, wire and instrumentation; electrical service up to and including 13.8 KV. Mechanical Equipment: Setting and alignment, including pumps, motors, turbine and generator; multiple heavy rigging and lifts; Process pressure piping including natural gas, air and water. Structural steel including ladders, columns, beams, platforms and decks; experience with torque specifications, layout and shop drawings.
 Client: State of Georgia, USA.
Turbine Technology Services.
Project Description: Relocation of two units from Korea and one unit from Canada to Georgia. Scope included: unit disassembly; overhaul and refurbishment of units, including IGV replacements; unit installation; DER (DLN) gas fuel system conversions; turbine control system upgrades; balance of plant control; unit commissioning and start-up; resident engineering services and long term field service, component repair and parts support. Allen Bradley PLC5, ElectroFlo® Valves, DER Hardware, DER Gas Skids.
 Client: State of North Carolina, USA
Turbine Technology Services (TTS).
Project Description: Control system upgrade, SSS-clutch installation, fuel system modification, speed detection upgrade and hydraulic ratchet modification. GE Fanuc 90/70 with Genius I/O, Four ElectroFlo® Valves, Four SSS-Clutches, Flow Dividers, Magnetic Speed Pickups.
Home | |
